Almost everyone knows that a water heater needs maintenance regularly to run correctly and efficiently. It's only the lack of priority they assign to such a task that time gets the better of it. The instructions in the owner's manual are directly mentioned, and people overlook those procedures quite dramatically.
Did you know, you can totally avoid the situation of water heater repair? Let's dive deep into the details to let you know the life expectancy of a water heater you just bought. Firstly, you need to understand the ingredients which lead to deterioration. The perspective of the article is to implement solutions first and find out the risks avoided through each of them.
The basic regular servicing
Did you know that a water heater can last for 8 to 12 years? But the fact only applies for the regularly maintained bits. Although water heaters can be maintained by third-party help, it's your duty to implement the basics regularly. Routine servicing doesn't require a professional. The only equipment required are a screwdriver, a bucket and a skilled homeowner and you are good to go. Make sure you locate the exact place and determine if it is powered by electricity or gas.
Perform the mini flush
There is a lot of sediments and debris which settle on the bottom of the tank if not cleaned from time to time. It's not only water which goes inside the tank but a lot of dirt and minerals. The end result is corrosion of the surface. The solution is right in front with a complete flush of water from the tank. It takes just a small fraction of your day and can be done with the water heater still working. Following are the steps to flush the tank.
Testing the temperature and pressure valve
It is a critical safety feature in every water heater which senses pressure buildup and excessive temperature. Once the pressure and temperature reach an extent, it automatically opens to release it out of the tank. In the absence of this feature, water is at risk of explosion. The T and P valve is located at the top of the tank. Follow the steps mentioned below.
Bring the temperature down.
The default temperature of a water heater is 130 to 140-degree Fahrenheit. It is recommended to keep it set at 120 for most households to fulfill their requirements. This not only brings down the energy consumption but also avoids the accumulation of debris at the bottom of the tank.
If each of these functions is performed correctly, there are more chances that the water will last for more than the expected time. For further specific details, ask your plumber to provide insights about your water heater in Scottsdale.
Did you know, you can totally avoid the situation of water heater repair? Let's dive deep into the details to let you know the life expectancy of a water heater you just bought. Firstly, you need to understand the ingredients which lead to deterioration. The perspective of the article is to implement solutions first and find out the risks avoided through each of them.
The basic regular servicing
Did you know that a water heater can last for 8 to 12 years? But the fact only applies for the regularly maintained bits. Although water heaters can be maintained by third-party help, it's your duty to implement the basics regularly. Routine servicing doesn't require a professional. The only equipment required are a screwdriver, a bucket and a skilled homeowner and you are good to go. Make sure you locate the exact place and determine if it is powered by electricity or gas.
Perform the mini flush
There is a lot of sediments and debris which settle on the bottom of the tank if not cleaned from time to time. It's not only water which goes inside the tank but a lot of dirt and minerals. The end result is corrosion of the surface. The solution is right in front with a complete flush of water from the tank. It takes just a small fraction of your day and can be done with the water heater still working. Following are the steps to flush the tank.
- Locate the drain valve and place a bucket underneath.
- Turn the valve clockwise to release at least one gallon of water into the bucket. You might require a screwdriver to rotate the drain valve. The quantity of water to be drained further depends upon the capacity of the water heater.
- The water will be very hot, so be careful.
- Close the valve by turning it the other way around.
- If you are unable to open the valve, contact a water heater repair service in Scottsdale.
Testing the temperature and pressure valve
It is a critical safety feature in every water heater which senses pressure buildup and excessive temperature. Once the pressure and temperature reach an extent, it automatically opens to release it out of the tank. In the absence of this feature, water is at risk of explosion. The T and P valve is located at the top of the tank. Follow the steps mentioned below.
- Locate the valve and place a bucket at the end of the discharge tube.
- Lift the lever of the valve to open it manually. Stay away from contact with the hot water.
- Let the water flow for a few seconds and then release the lever back to normal, stopping the water flow.
- If the valve does not open or hints a leak, contact a professional plumber.
Bring the temperature down.
The default temperature of a water heater is 130 to 140-degree Fahrenheit. It is recommended to keep it set at 120 for most households to fulfill their requirements. This not only brings down the energy consumption but also avoids the accumulation of debris at the bottom of the tank.
If each of these functions is performed correctly, there are more chances that the water will last for more than the expected time. For further specific details, ask your plumber to provide insights about your water heater in Scottsdale.
Comments
Post a Comment